Hair planting machine_high-speed hair planting machine_brush making equipment

Hair planting machine - processing method and teaching data of hair planting machine
Automatic processing of hair planting machine:
It is to continuously process products without stopping in the middle. Unless the 'stop' button is pressed, the cyclic processing of products can only be realized when more than 2 fixtures are placed. Fully automatic processing can improve production efficiency. When the product on the first fixture is processed and the product on the second fixture is processed, the product on the first fixture can be replaced, and the product on the second fixture can be processed. The product on the first fixture can then be replaced to achieve reciprocating processing. If only one fixture is placed, only semi-automatic machining mode can be used. In the standby state, press the number key '1' on the panel to enter the fully automatic working mode. When the protection occurs, the entire mechanical action stops. After repairing, move the machine head to the high position, and use the 'Single' key to find the If there is an empty space, then press the 'Start' key to process, otherwise, in the original machined hole position, press the start key to process a heavy hole phenomenon, which may damage the needle. Be careful during operation, and you should also pay attention to semi-automatic machining.
Semi-automatic processing:
Press the 'Start' key once to process once. After the product is processed, the machine head stops at a high position and runs to the starting point. Change the product, press the 'start' key again, run to the first hole position, and process it again, or start from the Nth hole to process a hole, N can be set, you can input the hole number through the keyboard, press the Press the 'Hole' key to run to the hole, make sure that the hole has not been processed, and then press the 'Start' key to process, otherwise the needle will be damaged. When protection occurs, the processing method is the same as that of automatic processing.
Fully automatic test machine:
After teaching the data of the product, in the fully automatic test machine screen, press the 'up hole' or 'down hole' button to realize single-step hole alignment, you can check whether the position of the hole is wrong, if it is wrong, you can exit and enter Modify it in the teaching editing interface. After pressing start, the worktable will continue to move until a product program file is finished and stop working, so that the teaching data of the hair planting machine can be used.

Test whether the workbench is normal.
The hole position of the hair planting (drilling) machine is related to the teaching. The order of the teaching data is the order of the hair planting (drilling). After completing a hole position, return to the first hole position, and try to make the first one and the first one. A hole is similar. The number of holes (the first hole to the first hole) contained in a product number is called a product or a style (or a program data file), and the data of a product or a style can contain several A fixture, the distance between two fixtures (a hole of the fixture and the first hole of the next fixture) is called the distance between the two holes. The 0th hole position is called the starting position or the processing zero position, not the mechanical zero position. The order of flocking (drilling) must be drawn up first to ensure speed.
0 point zero point or start point
The order of the teaching data is the order during processing, so try to make the distance between the holes taught as small as possible. The teaching data can be taught horizontally or vertically. The numbers marked in the above figure are the sequence of the teaching holes. In this way, the distance between the two taught points is short, and the running time of the motor is short. When one motor runs, the mechanical vibration will also be reduced. Small, the route of flocking or drilling is serpentine. If possible, arrange the holes so that the first hole is close to the first hole, so that the speed will be faster and the efficiency will be higher.
Teaching rotation is almost the same as teaching plane. When teaching rotation, you should pay attention to it. When the workpiece rotates forward 360 degrees, do not continue forward rotation, but reverse the teaching data. This is similar to plane teaching. The data is increasing all the time, resulting in a large distance between one hole and the first hole. Suppose 20 revolutions. When one hole is finished, the motor will rotate 20 revolutions when returning to the first hole, and the speed is 15 revolutions per second. , it takes 2 seconds, which is 2 seconds longer than the forward and reverse teaching a product to run, and the output is very different. Therefore, when teaching, it is necessary to first formulate the order of processing holes, and find a good method, which can improve production efficiency.
When the hair planting machine enters the teaching screen, you must press the 'Zero' key, the machine platform will return to the origin, and then teach the data, otherwise the obtained data will be inaccurate or cannot be taught. Then select the speed grade (1, 2, 3 correspond to low, medium, and teaching speed), press (X+, X-, Y+, Y-, Z+, Z-) to move the platform to the first hole point, and then press ' 'Enter' key, for the first hole point, then teach the second, third hole and so on.
Hair planting machine