The operation instructions of the brush machine production equipment carding machine are as follows: 1. Connect the power supply correctly according to the rotation direction of the motor, and be sure to connect to the ground wire safely and place it stably. 2. After the power is turned on, press the 'green' button, the suction fan starts (that is, the dust exhaust fan works), the two inverters are powered at the same time, and the standby state is displayed, and the panel displays '0' at the same time. Press the 'red' button. stop working. 3. There are two positioning fixtures on the feeding table, which are positioned by the tip of the hair, that is, combing with a handle. This combing method can press tightly and the brush is not easy to be damaged. Another method is to use the iron shell to position the brush. This combing method can put the brush quickly, but the thickness of the brush head is not uniform, which is easy to damage the brush head. At the same time, high pressure will also damage the brush head brush head. 4. According to the thickness of the brush, adjust the lifting screws at both ends of the machine, so that the brush is pressed tightly and smoothly enters the engine room with the rubber chain, and the compression spring is in a stressed state (that is, the lower end of the M12 double nut and the groove iron plane are raised by 3mm ~5mm clearance is sufficient). 5. If there is too much waste hair in the rubber chain and sprocket tooth groove, it should be cleaned in time, otherwise the chain slips, the pressure is not tight, and the dislocation is easy to cause damage to the brush and damage to the rubber. At the same time, add some lubricating oil to the chain and sprocket. The gearbox oil is changed every 500 hours of operation. Change the oil within 1 week for the first time. 6. Operate the keys of the inverter according to the instruction manual of the inverter. After the inverter is electrified and displays '0', press the green button 'RUN' of the inverter to start the operation and return to the last memory work, and press the red button to stop the inverter. The upper rotary button is for speed regulation. The voltage of the machine is too low; the temperature of the motor is too high; the combing load is overloaded, etc., the inverter has a protective effect, and the specific settings and operation are according to the inverter manual. 7. When combing the bristle brush, the speed of the roller is generally at a medium speed, and the chain drive can be slightly faster. When combing the wool brush, the speed of the roller should be increased, and the chain drive should be slow; the speed of the silk brush roller should be slow. Specifically set according to the requirements. 8. The front end of the iron shell of the brush is 3-4mm smaller than the front end of the rubber. As long as the needle cannot hit the wooden strip inside the brush, the brush is not easy to be damaged. 9. Regularly check the air outlet of the fan and clean up the waste hair, otherwise the motor will be damaged easily if the air exhaust is not smooth. 10. When the roller is running, it is strictly forbidden to open the upper cover to work. 11. Do not operate the machine during lightning. 12. Common faults and troubleshooting methods: 1. The bristle brushes and wool brushes are not cleaned properly. ① Increase the rotation speed of the roller and slow down the transmission speed of the chain; ② Try to adjust the brush as close as possible to the direction of the roller, as long as the needle does not touch the filling strip in the brush head, and the bristles are not damaged. 2. The filaments of the wire brush are bent and deformed, which mainly reduces the speed of the rollers, and at the same time, the speed of the chain transmission can be adjusted faster. 3. The rubber chain of the bottom row is easy to fall off the rubber or the chain makes abnormal noise. Clean up the waste hair in the double-row sprocket groove in time, add lubricating oil (evenly, a little), and tighten the chain. 4. The brush head is easily sucked into the machine compartment. ①Adjust the pressing screw to press the brush head tightly; ②Exclude the thickness of the brush head; ③The brush head cannot be in the shape of a waist drum (the middle protrudes); ④If it is a drum shape, leave a gap between the brush head and the brush head. There are gaps. 5. The adjustment speed of the inverter is unstable. If you use the rotary adjustment switch, it is very likely that the adjustment switch is damaged. Refer to the 'Instruction - Function Parameter List' to modify the parameters, and change the F0.00-0 to F0.00-1, then use the up and down keys to set the speed. 6. The sound is abnormal when the machine is just started. ① There may be a phase loss, check the circuit; ② Check the contactor, the voltage is unstable, and it is easy to damage the contactor; if the dust enters the contactor, it is also easy to cause poor contact, dust removal or replacement of the contactor. 7. The machine trips. Check the circuit and check one by one, it is very likely that a motor is burned out and short-circuited. Pay attention to the lack of phase, the lack of phase is the most likely to damage the motor. 8. The machine has induction electricity, and the ground wire must be connected well. Previous: Common faults and solutions of hair planting machineNext: The case of flat yarn machine and the selection of flat yarn
